Rapid City Plumbing — Water Heater Experts Call 24/7605-877-5050 Request service

Furnace problems we fix in Rapid City

  • No heat at all — dead igniter, failed gas valve, tripped rollout switch, bad control board
  • Blowing cold air — dirty flame sensor, cracked igniter, high-limit trip from a clogged filter
  • Short cycling — airflow starvation, flame sensor, thermostat, or an oversized unit
  • Blower won’t run, or runs constantly — capacitor, blower motor, control board, fan-limit settings
  • Loud bang on startup, rattling, squealing — delayed ignition (dangerous, call), loose panels, blower bearings
  • Furnace won’t stay lit — flame sensor, pressure switch, blocked inducer or intake/exhaust vent iced over in a storm
  • CO detector going off — leave the house, then call us and the gas company; cracked heat exchangers happen on older furnaces

What a furnace visit looks like

We start with what you’re seeing, check the obvious (filter, switch, breaker, thermostat, vents), then run the sequence of operation: thermostat call → inducer → pressure switch → igniter → gas valve → flame sense → blower. That finds the failed part instead of guessing. You get a price before we replace anything, and the parts that fail most on Rapid City furnaces are on the truck.

Tune-up before the cold snap

A fall tune-up — clean the flame sensor and burners, test the igniter, check the heat exchanger and CO, verify gas pressure and temperature rise, replace the filter — is how you avoid the January no-heat call. It’s the same visit we’d recommend for a boiler; in a boiler home the water heater is on the same system, and we do both.

Furnace replacement

When it’s time, we size the new furnace to the house (not to the old furnace, which was probably oversized), install a 95%+ efficient unit with proper PVC venting and condensate handling, and set it up so it runs quietly and evenly. Financing questions — ask when you call.

Need it fixed today?

A real person answers, day or night. Most Rapid City calls: within 60 minutes or less.

605-877-5050

Upfront price before any work starts.

We call back, we don’t email back. Emergency? Don’t wait on the form — 605-877-5050.

$35 Off Any Service Call coupon from Rapid City Plumbing

Questions we get about furnace repair

My furnace runs but blows cold air. What is it?

Usually one of three: the flame sensor is dirty and shutting the burner down (a 10-minute clean), the igniter has cracked (a common part we carry), or the high-limit switch is tripping because the filter is clogged and the furnace is overheating. Check the filter first — if it’s gray and packed, replace it and try again before you call.

Why does my furnace turn on and off every few minutes?

Short cycling. Most often a dirty filter or blocked return starving airflow, a failing flame sensor, or an oversized furnace. It wastes gas and wears out the igniter fast — worth a visit before it becomes a no-heat call.

Should I repair or replace my furnace?

Under 12 years old and the repair is a part — repair it. Over 15, a cracked heat exchanger, or a second major repair in two winters — replace it. A cracked heat exchanger is a carbon monoxide risk and we will not patch it. We quote both options with numbers, on site.

Do you come out at night for no heat?

Yes — 24/7. A real person answers and a tech is dispatched; most Rapid City no-heat calls see us within 60 minutes or less. Nights and weekends carry a dispatch fee we quote on the phone. While you wait: set the thermostat to heat and 5° above room temp, check the breaker and the furnace switch (looks like a light switch, near the unit), and make sure the filter isn’t packed.

No hot water? No heat? A leak?

A real person answers, 24/7. Upfront price before we start. Fast. Friendly. Professional.